 True Temper GS95 Trim |
Posted by Brent Mazur on 2009-18-11 11:36
Are there Trim instructions for the GS95 Irons If not Do I order the 40 inch and Butt Trim the irons to my desired length( Read More... | 1 comments )
| I MIX |
Posted by michael on 2009-03-11 17:38
Hi what problems if any is there in re-shafting a i mix head on a callaway and what components do you need and where can you get them( Read More... | 0 comments )
| Iron Shaft Tip Trimming |
Posted by Pat on 2009-22-10 09:51
If you trim the tip of a Dynamic Golf iron by shaft by 1-2" and still leave the overall length at +3/4" what happens to the playability of the iron?
...( Read More... | 1 comments )
| Tip trimming Rifle shafts |
Posted by Eric Haechrel on 2006-21-06 00:02
I have a set of Rifle 5 5 shafts (3-PW) The 6-iron tip is bent so I need to replace it Can I use the 3-iron shaft if I tip ...( Read More... | 4 comments )
| nv trim |
Posted by michael on 2009-03-09 10:57
Hi I have installed a 50gramm reg nv in my burner driver that had about 1 and quarter inches removed from the tip by mistake but it plays ok for ...( Read More... | 2 comments )
| Tip Trimming For Hybrids |
Posted by Howard Freed on 2009-11-09 15:23
Recentlty made a Q4U Hybrid 19 degrees using an XPC Fairway Wood shaft tip-trimmed 1 inch which is the recommended trim for a 5-wood Now my customer wants the 24 ...( Read More... | 0 comments )
| Shaft Trimming |
Posted by Mark on 2009-30-08 18:12
I am using a Graphite Design Aura Green shaft for a 7 wood The instructions that came with the shaft says to trim 1" This does not seem right A ...( Read More... | 2 comments )
| Need Tip Trim specs for V-SE70 irons #6588I- R |
Posted by Ron on 2008-11-12 17:12
Are these the same as the Aldila HMV3 Plus? 3-1/2" on PW/9i and 1/2" on the 3i with 1/2" increments?
I can't seem to get a definitive answer from anyone ...( Read More... | 4 comments )
| Trimming for Snake Eyes Approach Hybrids |
Posted by Terry on 2009-27-08 14:46
I am using a Graffaloy Attack Lite Iron Shaft for a 35 degree and a 39 degree Snake Eyes Approach Hybrid head What do I need to trim off the ...( Read More... | 0 comments )
| steel shaft trimming for tt lite metal wood |
Posted by Cragar on 2009-26-08 20:33
What are the trim requirements for tip and butt on a TT Lite steel shaft for a metal driver? It is an 450 cc driver( Read More... | 1 comments )
| cutting down irons |
Posted by D on 2009-11-08 09:46
If I cut a set of irons 1 1/2" down from the butt end will that significantly affect the siffness?( Read More... | 1 comments )
| synchron tip trimming |
Posted by kevin on 2009-31-07 10:44
Have just purchased some ladies synchron tour series shafts by aldila wondered if anyone could help with trimming instructions as i have no reply from aldila themselves( Read More... | 1 comments )
| Triming in Graphite Design Aura Blue |
Posted by Hilton on 2009-24-07 09:10
I bought a wod shaft graphite design aura blue to assemble a wood #3 It's a regular flex shaft
Where should I cut this shaft and how much should ...( Read More... | 2 comments )
| two questions |
Posted by michael on 2009-24-07 05:52
Hi would trimming a driver shaft by say quarter inch alter spin that you receive ie lower launch ?And would it alter torque of a shaft ? ie stiffen the ...( Read More... | 1 comments )
| Trimming instuctions for Dynamic Gold 3-SW |
Posted by Bill Wood on 2009-08-06 14:52
I'm building a set of clubs and have purchased a set of Dynamic Gold Regular steel shafts I was hoping the set would come with trimming instructions but they did ...( Read More... | 2 comments )
| Soft-stepping Python Iron Shafts |
Posted by Jody Smith on 2009-29-06 10:58
I need to replace a regular flex graphite Python iron shaft in my son's set Can I soft-step a stiff flex to perform like a regular flex as this is ...( Read More... | 2 comments )
| TT Dynalight iron shaft parallel tip |
Posted by Andrew on 2009-25-06 01:18
I believe the Dynalight Gold and Gold SL versions come in separate R and S flexes How do they differ from the original Dynalight iron shaft that came in the ...( Read More... | 0 comments )
| Abrading Graphite Shafts |
Posted by Chick on 2009-19-06 10:22
When abrading the tip of a graphite shaft is it necessary to remove coating and paint down to the black or just the clearcoat leaving the paint? Thanks for any ...( Read More... | 4 comments )
| shaft trimming |
Posted by don on 2009-22-06 21:32
I HAVE A PROFORCE CLASSIC 65 350 WOOD SHAFT TO GO IN A TAYLORMADE 360 TI IT SAID NO SHAFT TRIM FOR DRIVER DO I STILL HAVE TO TAKE OFF ...( Read More... | 0 comments )
| shaft installation |
Posted by CHARLES on 2009-10-06 14:32
Does anyone have shafting instructins for nippon shafts? I assume they are butt trim for irons( Read More... | 1 comments )
